P1108 Engine Trouble Code

When you check engine light came on code P1108 the reason should be Engine Light ON (or Service Engine Soon Warning Light). However your vehicle's manufacturer may have a different definition for the P1108 OBD-II Diagnostic Powertrain (P) Trouble Code. So you should chech it on our car models.
When the DTC check engine light comes P1108 code on the first you can check is the gas related maybe gas cap. Pull over, retighten it, and take a look at the cap to see if it has any cracks inside. Go on driving and to see if the check engine light turns off automaticly. On the other hand, you can buy a gas cap for about $4.5 at an auto parts store. All you need to do is take the old one take off and take on the new one. If you've already bought it to the store, you might as well just replace the cap. While not car-threatening, it's good to take care of this right away to improve gas mileage/km.
P1108 Code Meaning :
OBD-II Diagnostic Powertrain (P) Trouble Code For Engine
Fuel And Air Metering
Engine Oil Temperature Sensor Malfunction
Cylinder 10 Contribution/balance Fault
Timing Reference High Resolution Signal A Too Many Pulses
The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.
P1108 OBD-II Diagnostic Powertrain (P) Trouble Code Description
P1108 OBD-II Trouble Code Dual Alternator Battery Lamp Circuit Malfunction is one of the definitions for the P1108; however your vehicles manufacturer may have a different definition for the P1108 code. Please check below for P1108 code. Engine Oil Temperature Sensor Malfunction and Cylinder 10 Contribution/balance Fault causes most of code P1108.
Reason For P1108 Code
The reason of P1108 OBD-II Engine Trouble Code is Engine Oil Temperature Sensor Malfunction.P1108 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is over-retarded, the engine trouble light will be illluminated and the code will be set.
How To Repair P1108 Code
Before starting let's see P1108 repairing process steps:
- Qualified technicians will begin by using a scan tool to access P1108 code stored in the ECU.
- Technicians will note P1108 code present and any freeze frame data associated with them.
- After all, if you sure the engine trouble is finished, the code will be cleared.
B for the vehicle's clutch is giving the wrong voltage readings, there could be an issue with the solenoid, the sensor, the wiring, or with the clutch itself. Shifting may become harsh, and other transmission problems may occur.
This process helps the mechanic narrow down the exact cause of the issue. If the transmission fluid fix did not cause the code to disappear from the PCM, then next step is to inspect the electrical components, and to continue working through possible repairs until the correct issue is found.
Sometimes P1108 code comes with P110800 code.Diagnosis Of Engine Error OBD Code P1108
It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a P1108 trouble code to be stored
The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the P1108 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.
The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.
Cars With Same Problems :
- Toyota Sa P1108 Trouble Code
- Lagonda 3-litre P1108 Trouble Code
- Chery A1 P1108 Trouble Code
- Oldsmobile 4-4-2 P1108 Trouble Code
- Prince B P1108 Trouble Code
- Volkswagen 1200 P1108 Trouble Code
- Ford Everest P1108 Trouble Code
- Holden Wb P1108 Trouble Code
- Nissan Mid4 P1108 Trouble Code
- Alvis Tf21 P1108 Trouble Code
- Pininfarina Hit P1108 Trouble Code
- Mazda Protege P1108 Trouble Code